LIFETIME FILTER- Simply Inspect, Clean and Reuse!!!

Oil Filters: Superior Filtration

This should be the last oil filter you will ever buy! Made from laser cut, medical grade, 304 stainless steel micronic filter cloth, this filter provides 200% more filter area in many cases. Most good paper filters will pass particles in the 90 to 95 micron range, and some tested, as much as 300 microns. Sand is about 125 microns and a white blood cell approximately 25 microns. Our stainless filter catches items down to 35 microns "absolute", which is about 3 times better than most good paper or brass filters. The pleat seam is welded, able to withstand up to 600 degrees in our filter, not glued, like paper filters.

Cleanable and Reusable

Simply remove the filter, rinse in clean solvent and replace it, you're done. The filter can be cleaned with solvent, kerosene, aerosol carburetor cleaner, or any other degreasing agent, even common dish soap. You can even blow air through the filter from the inside out to remove any small particles or cleaning agent from the screen if you so desire.

Consistent Flow Under All Conditions

Stainless steel will stand up to the stress of heat, high pressure and physical handling much better than paper or brass. This filter maintains consistent flow under all conditions including cold start ups and or under extreme heat. A one inch square of this micron filter material will flow 1.9 gallons of 90 weight oil per minute at only 1 psi pump pressure (70 degrees F). Our typical filter size is 30 sq. in. which equals the flow of 57 gallons per minute. Standard paper filters do not flow well when the oil is cold, often causing the bypass valve to open allowing unfiltered oil to enter your engine.

Magnetic Prefiltering!

A super-strength nickel plated Neodymium rare earth magnet is placed in the top of the filter element to pre-filter ferrous material out of the oil before it passes through the engine.

Cooling!

The billet aluminum finned housing also acts as an oil cooler. Customers have reported seeing between 4 and 7 degrees of oil temperature reduction using the K&P filter over a stock paper filter. Every little bit helps.

Horsepower!

Differential pressure between the outside of a filter element and the inside can get to around 20 lbs at high engine RPM. This filter measures less than 1 lb at high engine RPM, reducing the parasitic horsepower need to run the oil pump, leaving more horsepower for the rear wheel!

Unaffected by Water, Heat and Pressure!

This filter is capable of withstanding extremely high pressure and flow rates. It is also unaffected by Water, Heat and Pressure, unlike standard paper filter material which swells in the presence of water, closing off filter pores and reducing flow.

Early Detection!

By allowing you to inspect the debris that is in the filter you can monitor your engines condition, avoiding minor and or catastrophic failures.

What is a Micron?

A micron is one thousandth of a millimeter. That's about .00003937 inches. Fine sand can be as small as 62 microns thick. Our filter will not allow any particle over 35 microns to pass through this filter, that's some pretty small stuff that's being caught.

So who uses this type of filtration?

This high tech filter technology is widely used in all types of auto racing including NASCAR, Indy type cars, Formula 1 and in the Aerospace industry where filtration is of the utmost importance.

Things to think about:

Next time you are fanning your clutch think about all that tiny debris that is created from the clutch and gears meshing together, spinning around in your motor's vital parts. If you really care about the life of your motor and consider the cost of loss of time associated with a current day 4-stroke motor, then you need one of these filters. It's even transferrable in some cases to your next bike. I used the same filter in my last three bikes, and it's still like brand new, there's simply nothing to wear out.

Environmental benefits:

In addition to all the other benefits, our filter helps keep the land fills free of old used filters.

LIFETIME FILTER- Simply Inspect, Clean and Reuse!!!

*Meets or exceeds filtration of stock filters!

*Magnetic pre-filtering of ferrous materials!

*Much higher flow-rate and reduced differential pressure reduce the chance of oil bypassing filter media on cold start up and high engine RPM!

*Billet aluminum housing acts as an oil cooler!

*Lower differential pressure reduces parasitic horsepower loss at the oil pump!

*Easy inspection of what is being filtered out of the engine!

*Beautiful chrome finish available for ease of maintenance and show-quality shine!

*Machined finish is easily polished and can be customized by you!

*Cup Wrench Included!